Hydrogeomatics · Equipment reference

BYNAV Gmouse-M20

Technical specification sheet and integration notes for hydrographic positioning.

Compiled 11 October 2026 · Document HG-GM20-01 · Revision 1.0
Hydrogeomatics websiteManufacturer references
1 cm + 1 ppmHorizontal RTK · typical RMS [1]
10 HzM20 GNSS results [1]
550 mWTypical Gmouse power [1]
Manufacturer-based reference

Product identification

Gmouse-M20 is a module-integrated RTK antenna in BYNAV’s Gmouse-M2 family. [1]

This sheet covers the complete Gmouse unit. Specifications for the bare M20 OEM module are not substituted for enclosure or cable specifications.

Model distinction: the manufacturer’s inertial and dead-reckoning tables identify M21/M22. Their 100 Hz INS output and DR figures are not assigned to M20 here. [1] No heading, roll, pitch or heave accuracy is claimed for this model.

Positioning and measurement

ParameterPublished value [1]
Single-point horizontal / vertical1.5 m / 2.5 m RMS
RTK horizontal / vertical1 cm + 1 ppm / 1.5 cm + 1 ppm RMS
Carrier phase / pseudorange≤1 mm / ≤0.1 m RMS
Velocity accuracy0.03 m/s RMS
Timing20 ns RMS; optional; RF/antenna bias excluded
Dynamic velocity / acceleration≤500 m/s / ≤4 g

Typical performance depends on satellite geometry, baseline, multipath and interference. [1]

Interpreting ppm: 1 ppm adds 1 mm per kilometre of baseline. Arithmetic examples: at 1 km, horizontal RTK is 11 mm and vertical RTK 16 mm; at 10 km, 20 mm and 25 mm respectively. These are evaluations of the published expressions, not field test results or maximum-error guarantees.

Satellite signals and interference

System / featurePublished support [1]
GPSL1 C/A, L1C, L2, L5
GLONASSG1, G2
BeiDouB1I, B2I, B3I, B1C*, B2a, B2b
GalileoE1, E5b, E5a, E6*
QZSSL1 C/A, L2, L5, L6* (CLAS)
L-Band*−133 dBm; FEC 10−5
Anti-jamming65 dBc ISR; multitone, narrowband, fast sweep

* Optional or firmware-dependent. [1]

Signal availability is not proof that a correction service is included. Confirm regional service availability, activation, firmware and any subscription separately.

Hardware and interface verification

The following complete-unit details were not verified from an accessible manufacturer manual during this review. Obtain the exact part-number documentation before installation.

ItemRequired confirmation
Enclosure dimensions and massGmouse-M20 overall drawing, cable allowance and mounting arrangement.
Electrical supplyPermitted input range, polarity, startup current, connector pinout and protection requirements. Typical power is not a supply-voltage specification.
Data connectionCable option, electrical signalling standard, baud rates and adapter requirements. Do not assume TTL, RS-232, USB or Ethernet from the product name.
Position / correction messagesEnabled output sentences, datum, timestamps, correction-input format and firmware commands.
Time synchronizationAccessible PPS or event connector, pulse settings and time scale, if required.
Environmental protectionIP rating, connector sealing, operating/storage temperature and salt-water suitability.
Package and certificationSupplied accessories and conformity documents for the actual unit. Company-wide or OEM-module certifications are not treated as Gmouse-M20 certification.
Hydrogeomatics engineering guidance

Integration into a sounding system

The guidance below is an integration checklist, not a manufacturer performance claim or a statement that this receiver alone meets a particular survey standard.

Position and correction workflow

  1. Mount the antenna with a clear sky view and survey its position relative to the vessel reference point.
  2. Provide compatible base-station or network corrections through a verified connection.
  3. Configure compatible position messages and timestamps for the survey software.
  4. Log solution status, correction age and quality indicators alongside the sounding records.

Coordinate and timing control

  • Set the project datum, epoch, projection and vertical reference explicitly.
  • Record antenna-to-transducer X/Y/Z offsets and the coordinate sign convention.
  • Measure latency between positioning and echo-sounder observations.
  • Use a separate verified motion/heading source wherever the survey requires it.
10 Hz in practice: one result every 0.1 second. At 2 m/s the vessel travels 0.2 m between results; at 5 m/s it travels 0.5 m. These are calculated sampling distances, not positioning errors. Time alignment and interpolation need separate assessment.

Vertical observations

Confirm whether the logged height is ellipsoidal or orthometric and document any geoid model. Tide reduction, chart-datum conversion, vessel motion, draft and transducer offsets require their own corrections. Do not use the RTK vertical accuracy figure as the complete depth uncertainty.

Commissioning and acceptance record

Keep an installation record that connects the actual receiver configuration to the project requirements.

CheckEvidence to retain
IdentityLabel photograph, serial number, exact model, firmware and activated options.
CommunicationsPinout, supply measurement, port settings, output format and correction connection.
Static verificationRepeated observations on an independently established control point with the same datum.
Dynamic verificationTime-aligned survey logs, repeat-line results and latency assessment.
Correction interruptionObserved loss/recovery behaviour and survey-software handling of degraded solutions.
Vessel geometryMeasured lever arms, antenna height, mounting photographs and offset sign convention.
Project acceptanceRequired uncertainty, rejection criteria, reviewer and signed configuration record.

Sources and document scope

  1. BYNAV official Gmouse product page — numerical tables and model distinctions used above; accessed 11 October 2026.
  2. BYNAV Gmouse-M20/M21/M22 manual (Chinese) — reference link; full PDF could not be retrieved during this review.
  3. BYNAV official technical support and download centre — request the current Gmouse manual, applicable interface protocol and configuration guidance.

Prepared independently by Hydrogeomatics. This is a sourced equipment reference with separately labelled engineering guidance, not a BYNAV-issued datasheet. Confirm the supplied configuration against current manufacturer documentation.